SZ196ZPA | Zero Pressure Accumulator SMART ZONE® Medium Duty Conveyor

Category: Accumulation Conveyors

SZ196ZPA | Zero Pressure Accumulator SMART ZONE® Medium Duty Conveyor - Image 2

SZ196ZPA | Zero Pressure Accumulator SMART ZONE® Medium Duty Conveyor - Image 3

Description
Specs

Roach SZ196ZPA Smart ZONE® safely accumulates packages with zero back pressure utilizing zone singulation operation. Loads up to 125 lbs./ft. may be effectively handled with its unique design. This conveyor features NO minimum weight limitations. Roach Smart ZONE® replaces sensor rollers with photo electric sensors to accumulate products with previously difficult minimal weight restrictions and is easy to install.

Specifications	TREAD ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S. PRESSURE ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S; 8″ BF with 6″ wide belt. RETURN ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S, adjustable. BELTING: 6″ wide black PVC-120 COS. DRIVE PULLEY: 4″ dia. with 1-3/16″ dia. shaft or 8″ dia. with 1-7/16″ dia. shaft; both crowned and fully lagged. END PULLEY: 4″ dia., crowned, with 1-3/16″ dia. shaft. BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings. SPEED: 60 FPM, constant. BED: 7″ x 1-1/2″ x 12 ga. channel frame slotted for tread rollers to pop-out. When unit is installed at 7′-0″ elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports. SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30′. FLOOR SUPPORTS: Optional MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor. ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base. ACCUMULATION: Zone singulation operation; 3″ RC = 2′-0″ long zones; 4-1/2″ RC = 3′-0″ long zones. 1′-0″ of live roller at each end of conveyor over end plates remains “live” during operation. Zones are pneumatically actuated using photo electric sensors. PNEUMATIC ACTUATION: Maximum air line pressure should not exceed 30 PSI. FRL: Unit is provided with filter, regulator, lubricator with 1/4″ ports. ELECTRICAL CONTROLS: Optional

Specifications

TREAD ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S.

PRESSURE ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S; 8″ BF with 6″ wide belt.

RETURN ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S, adjustable.

BELTING: 6″ wide black PVC-120 COS.

DRIVE PULLEY: 4″ dia. with 1-3/16″ dia. shaft or 8″ dia. with 1-7/16″ dia. shaft; both crowned and fully lagged.

END PULLEY: 4″ dia., crowned, with 1-3/16″ dia. shaft.

BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.

SPEED: 60 FPM, constant.

BED: 7″ x 1-1/2″ x 12 ga. channel frame slotted for tread rollers to pop-out. When unit is installed at 7′-0″ elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports.

SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30′.

FLOOR SUPPORTS: Optional

MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.

ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base.

ACCUMULATION: Zone singulation operation; 3″ RC = 2′-0″ long zones; 4-1/2″ RC = 3′-0″ long zones. 1′-0″ of live roller at each end of conveyor over end plates remains “live” during operation. Zones are pneumatically actuated using photo electric sensors.

PNEUMATIC ACTUATION: Maximum air line pressure should not exceed 30 PSI.

FRL: Unit is provided with filter, regulator, lubricator with 1/4″ ports.

ELECTRICAL CONTROLS: Optional

SZ196ZPA

Description
Specs

Specifications	TREAD ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S. PRESSURE ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S; 8″ BF with 6″ wide belt. RETURN ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S, adjustable. BELTING: 6″ wide black PVC-120 COS. DRIVE PULLEY: 4″ dia. with 1-3/16″ dia. shaft or 8″ dia. with 1-7/16″ dia. shaft; both crowned and fully lagged. END PULLEY: 4″ dia., crowned, with 1-3/16″ dia. shaft. BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings. SPEED: 60 FPM, constant. BED: 7″ x 1-1/2″ x 12 ga. channel frame slotted for tread rollers to pop-out. When unit is installed at 7′-0″ elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports. SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30′. FLOOR SUPPORTS: Optional MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor. ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base. ACCUMULATION: Zone singulation operation; 3″ RC = 2′-0″ long zones; 4-1/2″ RC = 3′-0″ long zones. 1′-0″ of live roller at each end of conveyor over end plates remains “live” during operation. Zones are pneumatically actuated using photo electric sensors. PNEUMATIC ACTUATION: Maximum air line pressure should not exceed 30 PSI. FRL: Unit is provided with filter, regulator, lubricator with 1/4″ ports. ELECTRICAL CONTROLS: Optional