Roach model 196LRC features tapered rollers to maintain product orientation. Reversible, it is also commonly slave driven from 196VP and 796CALR conveyors.
Roach model 196LRC features tapered rollers to maintain product orientation. Reversible, it is also commonly slave driven from 196VP and 796CALR conveyors.
| Specifications | TREAD ROLLERS: 2-1/2″ dia. to 1-11/16″ dia. x 14 ga. steel tapered rollers, model 254T; 1.9″ dia. x 16 ga. steel straight tangent rollers, model 196S. PRESSURE SHEAVES: Provides drive belt pressure to upper tread rollers. BELTING: “B” section V-belt. TAKE-UP: Screw type adjustable sheave with flat idler sheaves to maintain belt tension. TANGENTS: 1′-0″ both ends on 90 degree; 1′-6″ both ends on 45 degree; 1′-0″ both ends on 180 degree. Tangent roller centers provided on 3″ RC. SPEED: 60 FPM, constant. BED: 7″ x 1-1/2″ x 12 ga. formed steel channel frame. BEARINGS: End shafts are supported by precision, heavy duty, lubricated, ball bearing units with cast iron housings. ROLLER CHAIN: Drive shaft is driven by No. 50 chain. FLOOR SUPPORTS: Optional DRIVE LOCATION: Drive located on outside of curve. Specify left hand tangent length, right hand tangent length and drive location (“left hand drive” or “right hand drive”). NOTE: Drive hand determined with reference point located at outside of curve. For models slave driven (less drive), specify drive shaft location. CAPACITY: 500 lb. total distributed live load. MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor, located at infeed end of curve below bed on 45 degree and 90 degree curves; 3/4 HP supplied on all 180 degree curves. SPECIAL WIDTHS: Consult factory for pricing of ALL widths not shown. ELECTRICAL CONTROLS: Optional |
|---|
196LRC
Roach model 196LRC features tapered rollers to maintain product orientation. Reversible, it is also commonly slave driven from 196VP and 796CALR conveyors.
| Specifications | TREAD ROLLERS: 2-1/2″ dia. to 1-11/16″ dia. x 14 ga. steel tapered rollers, model 254T; 1.9″ dia. x 16 ga. steel straight tangent rollers, model 196S. PRESSURE SHEAVES: Provides drive belt pressure to upper tread rollers. BELTING: “B” section V-belt. TAKE-UP: Screw type adjustable sheave with flat idler sheaves to maintain belt tension. TANGENTS: 1′-0″ both ends on 90 degree; 1′-6″ both ends on 45 degree; 1′-0″ both ends on 180 degree. Tangent roller centers provided on 3″ RC. SPEED: 60 FPM, constant. BED: 7″ x 1-1/2″ x 12 ga. formed steel channel frame. BEARINGS: End shafts are supported by precision, heavy duty, lubricated, ball bearing units with cast iron housings. ROLLER CHAIN: Drive shaft is driven by No. 50 chain. FLOOR SUPPORTS: Optional DRIVE LOCATION: Drive located on outside of curve. Specify left hand tangent length, right hand tangent length and drive location (“left hand drive” or “right hand drive”). NOTE: Drive hand determined with reference point located at outside of curve. For models slave driven (less drive), specify drive shaft location. CAPACITY: 500 lb. total distributed live load. MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor, located at infeed end of curve below bed on 45 degree and 90 degree curves; 3/4 HP supplied on all 180 degree curves. SPECIAL WIDTHS: Consult factory for pricing of ALL widths not shown. ELECTRICAL CONTROLS: Optional |
|---|
196LRC
