Model 138LRC features tapered rollers to maintain product orientation. Reversible, it is also commonly slave driven from 138LR and 138VP making it the ideal curve in light duty applications.
Model 138LRC features tapered rollers to maintain product orientation. Reversible, it is also commonly slave driven from 138LR and 138VP making it the ideal curve in light duty applications.
| Specifications | TREAD ROLLERS: 1.9″ dia. to 1-3/8″ dia. x 16 ga. tapered rollers, model 138T; 1-3/8″ dia. x 18 ga., model 138G w/ 5/16″ hex, galvanized straight tangent rollers. ROLLER CENTERS: 1-9/16″ measured at inside radius of unit. PRESSURE SHEAVES: Provides drive belt pressure to upper tread rollers. BELTING: “B” section V-belt. TAKE-UP: Screw type adjustable sheave with flat idler sheaves to maintain belt tension. TANGENTS: 12″ both ends on 90 degree unit; 18″ both ends on 45 degree unit. BED: 6″ x 1-1/2″ x 12 ga. formed steel channel frame. BEARINGS: End shafts are supported by precision, heavy duty, lubricated, ball bearing units with cast iron housings. ROLLER CHAIN: Drive shaft is driven by No. 50 chain. FLOOR SUPPORTS: Optional MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor, located at infeed end of curve below bed. DRIVE LOCATION: Drive located on outside of curve. Specify left hand tangent length, right hand tangent length and drive location (“left hand drive” or “right hand drive”). NOTE: Drive hand determined with reference point located at outside of curve. For models slave driven (less drive), specify drive shaft location. CAPACITY: 300 lb. total distributed live load. SPEED: 60 FPM, constant. |
|---|
138LRC
Model 138LRC features tapered rollers to maintain product orientation. Reversible, it is also commonly slave driven from 138LR and 138VP making it the ideal curve in light duty applications.
| Specifications | TREAD ROLLERS: 1.9″ dia. to 1-3/8″ dia. x 16 ga. tapered rollers, model 138T; 1-3/8″ dia. x 18 ga., model 138G w/ 5/16″ hex, galvanized straight tangent rollers. ROLLER CENTERS: 1-9/16″ measured at inside radius of unit. PRESSURE SHEAVES: Provides drive belt pressure to upper tread rollers. BELTING: “B” section V-belt. TAKE-UP: Screw type adjustable sheave with flat idler sheaves to maintain belt tension. TANGENTS: 12″ both ends on 90 degree unit; 18″ both ends on 45 degree unit. BED: 6″ x 1-1/2″ x 12 ga. formed steel channel frame. BEARINGS: End shafts are supported by precision, heavy duty, lubricated, ball bearing units with cast iron housings. ROLLER CHAIN: Drive shaft is driven by No. 50 chain. FLOOR SUPPORTS: Optional MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor, located at infeed end of curve below bed. DRIVE LOCATION: Drive located on outside of curve. Specify left hand tangent length, right hand tangent length and drive location (“left hand drive” or “right hand drive”). NOTE: Drive hand determined with reference point located at outside of curve. For models slave driven (less drive), specify drive shaft location. CAPACITY: 300 lb. total distributed live load. SPEED: 60 FPM, constant. |
|---|
138LRC
Accumulation
Belt Conveyors
Belt Driven Live Roller
Chain Driven Live Roller
Flexible Conveyors
Gravity Conveyors
Line Shaft
MCS | Modular Connect System
MDZ | Motor Driven Zone Accumulator
Parts Conveyor
Plastic Belt
Powered Roller
Singulation
Slat Conveyors
Transfers
Wire Mesh Belt
Barrel Conveyors
Glass & Solar Handling
Heavy Duty Conveyors
laundry
Lumber
MDR | Motor Driven Roller Smart Conveyors
Sortation Conveyors
Special Transfers
Stackers/Destackers
Stops | Barriers | Walkovers
Tabletop Chain Conveyors
Transfer Carts
Turntables
Vertical Conveyors
Wheel & Tire Conveyors
© 2024 Roach Conveyors. All Rights Reserved