196ZPA | Zero Pressure Accumulator Medium Duty Conveyor

Category: Accumulation Conveyors

Description
Specs

Roach 196ZPA safely accumulates packages with zero back pressure utilizing zone singulation operation. Loads up to 125 lbs./ft. may be effectively handled with its unique design. This conveyor features NO minimum weight limitations. Sensor rollers are utilized to accumulate products with previously difficult minimal weight restrictions.

Specifications	TREAD ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S. PRESSURE ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S; 8″ BF with 6″ wide belt. RETURN ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S, adjustable. BELTING: 6″ wide black PVC-120 COS. DRIVE PULLEY: 4″ dia. with 1-3/16″ dia. shaft or 8″ dia. with 1-7/16″ dia. shaft; both crowned and fully lagged. END PULLEY: 4″ dia., crowned, with 1-3/16″ dia. shaft. BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings. SPEED: 60 FPM, constant. BED: 7″ x 1-1/2″ x 12 ga. channel frame slotted for tread rollers to pop-out. When unit is installed at 7′-0″ elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports. SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30′. FLOOR SUPPORTS: Optional MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor. ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base. ACCUMULATION: 2′-0″ long zones pneumatically actuated. 1′-0″ of live roller over end plates at each end of conveyor remains “live” during operation (# of zones x zone length + 2′ = overall conveyor length). PNEUMATIC ACTUATION: Maximum air line pressure should not exceed 30 PSI. FRL: Unit is provided with filter, regulator, lubricator with 1/4″ ports. ELECTRICAL CONTROLS: Optional

Specifications

TREAD ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S.

PRESSURE ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S; 8″ BF with 6″ wide belt.

RETURN ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S, adjustable.

BELTING: 6″ wide black PVC-120 COS.

DRIVE PULLEY: 4″ dia. with 1-3/16″ dia. shaft or 8″ dia. with 1-7/16″ dia. shaft; both crowned and fully lagged.

END PULLEY: 4″ dia., crowned, with 1-3/16″ dia. shaft.

BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings.

SPEED: 60 FPM, constant.

BED: 7″ x 1-1/2″ x 12 ga. channel frame slotted for tread rollers to pop-out. When unit is installed at 7′-0″ elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports.

SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30′.

FLOOR SUPPORTS: Optional

MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor.

ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base.

ACCUMULATION: 2′-0″ long zones pneumatically actuated. 1′-0″ of live roller over end plates at each end of conveyor remains “live” during operation (# of zones x zone length + 2′ = overall conveyor length).

PNEUMATIC ACTUATION: Maximum air line pressure should not exceed 30 PSI.

FRL: Unit is provided with filter, regulator, lubricator with 1/4″ ports.

ELECTRICAL CONTROLS: Optional

196ZPA

Need More Info?

Description
Specs

Specifications	TREAD ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S. PRESSURE ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S; 8″ BF with 6″ wide belt. RETURN ROLLERS: 1.9″ dia. x 16 ga. steel, model 196S, adjustable. BELTING: 6″ wide black PVC-120 COS. DRIVE PULLEY: 4″ dia. with 1-3/16″ dia. shaft or 8″ dia. with 1-7/16″ dia. shaft; both crowned and fully lagged. END PULLEY: 4″ dia., crowned, with 1-3/16″ dia. shaft. BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball bearing units with cast iron housings. SPEED: 60 FPM, constant. BED: 7″ x 1-1/2″ x 12 ga. channel frame slotted for tread rollers to pop-out. When unit is installed at 7′-0″ elevation or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with couplings and floor supports. SQUARING RODS: Adjustable rods on underside of bed allow frame to be squared for improved belt tracking and are standard on all units over 30′. FLOOR SUPPORTS: Optional MOTOR DRIVE: 1/3 HP, 230/460/3, 60 cycle, ODP right angle gear motor. ROLLER CHAIN: Drive pulley is driven by No. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives. Chain take-up provided on motor base. ACCUMULATION: 2′-0″ long zones pneumatically actuated. 1′-0″ of live roller over end plates at each end of conveyor remains “live” during operation (# of zones x zone length + 2′ = overall conveyor length). PNEUMATIC ACTUATION: Maximum air line pressure should not exceed 30 PSI. FRL: Unit is provided with filter, regulator, lubricator with 1/4″ ports. ELECTRICAL CONTROLS: Optional